Products >> Hollow Fiber UF Membrane >> Hydranautics UF Membrane

Hydranautics HYDRAcap MAX 60

Product No.：HYDRAcap MAX 60
Online Inquiry

Capillary Ultrafiltration Module HYDRAcap® MAX 60

Hydranautics HYDRAcap MAX 60 is a PVDF membrane capillary ultrafiltration module with outside to inside filtration mode.

HYDRAcap MAX 60 Data Sheet

Performance¹

Filtrate Flow:	11.7 – 37.9 gpm (2.7 – 8.6 m³/h)
Filtrate Turbidity:	≤ 0.10 NTU
Bacteria removal:	≥ 4 log

Type

Configuration:	Capillary Ultrafiltration Module
Membrane Polymer:	PVDF
Nominal Membrane Area:	840 ft² (78 m²)
Fiber Dimensions:	ID 0.024” (0.6 mm), OD 0.047” (1.2 mm)
Pore size:	0.08 micron

Application Data²

Typical Filtrate Flux Range:	20 – 65 gfd (34 – 110 l/m²/h)
Maximum Applied Feed Pressure:	73 psig (5.0 bar)3
Maximum Transmembrane Pressure	30 psig (2.0 bar)
Instantaneous Chlorine Tolerance:	5000 ppm⁴
Maximum Chlorine Exposure:	750,000 ppm-hrs
Maximum Feed Turbidity:	300 NTU⁵
Maximum Operating Temperature:	104 °F (40 °C)
pH Operating Range:	4.0 – 10.0
Cleaning pH Range:	1.0 – 13.0
Operating Mode:	Outside to Inside Filtration Dead End or Cross flow mode

Typical Process Conditions

Air Scour Rate:	7.3 - 9.1 acfm (12.3 - 15.4 m³/h)
Air Scour Duration:	120 - 240 seconds
Air Scour Frequency:	Once every 20 - 60 minutes
Maintenance Clean Frequency:	1 - 3 times per day
Maintenance Clean Duration:	20 - 30 minutes
Disinfection Chemicals:	NaOCl, ClO₂ or NH₂Cl
Cleaning Chemicals:	NaOH, HCl, H₂SO₄, or Citric Acid

Hydranautics HYDRAcap MAX 60 Module Dimensions

A, inches (mm)	B, inches (mm)	C, inches (mm)	Pipe connections	Dry Weight	Wet Weight
72.15 (1832.6)	63.11 (1602.9)	67.90 (1724.7)	2” Victaulic	115 lbs (52 kg)	200 lbs (100 kg)

Certifications: NSF61, NSF419 (US LT2ESWTR – Public Drinking Water Compliance)
¹ Typical module performance for most feedwaters.

² The limitations shown here are for general use. The values may be more conservative for specific projects to ensure the best performance and longest life of the membrane.

³ At 68°F (20°C). 58psi (4 bar) @ 86°F (30°C). 44 psi (3 bar) @ 104°F (40°C).

⁴ For 60 minutes or less.

⁵ Higher values can be treated. Consult Hydranautics's technical staff.

Notice: Hydranautics also offers HYDRAcap® MAX 60-NON, which is a dummy module with no potting or fiber.

Hydranautics believes the information and data contained herein to be accurate and useful. The information and data are offered in good faith, but without guarantee, as conditions and methods of use of our products are beyond our control. Hydranautics assumes no liability for results obtained or damages incurred through the application of the presented information and data. It is the user's responsibility to determine the appropriateness of Hydranautics' products for the user's specific end uses.

Version: 3/25/2016

Notice:
If your customer insists existing brand, please contact Hydranautics or it's distributors.
If you and your customer accept economical & quick-delivery equivalent of similar or better performance with same warranty, kindly send us an inquiry now.

Previous Product：Hydranautics HYDRAcap MAX 40 Next Product：Hydranautics HYDRAcap MAX 80